"Gone to the Beach" Necklace Inspiration from SWAROVSKI's Create Your Style

Create this DIY Swarovski Crystal Necklace Design with Instructions, that Incorporates the New Crystal Innovations.

Celebrate a sun-kissed summer with boho jewelry. This necklace is made using shell-like Mother of Pearl with Sea Snail Pendants and Jelly Fish Fancy Stones from Swarovski. Make and wear it with a sparkling megawatt smile!

Here are the Swarovski Crystals used in this necklace design:

Swarovski Crystal Fancy Stones 4195 - 14mm Cyrstal 3 pieces (please contact me for details)

Swarovski Crystal Fancy Stones 4195-22mm Crystal 2 pieces (please contact me for details)

Swarovski Settings 4195/S 1PH2OH  14mm Rhodium 3 pieces (please contact me for details)

Swarovski Settings 4195/S 1PH2OH 22mm Rhodium 2 pieces (please contact me for details)

Swarovski Crystal Beads 5000 - 3mm Crystal AB 52 pieces

Swarovski Crystal Pendants 6731 - 14mm Crystal AB 7 pieces

Supplies & Tools

Supplies

Chain, 10cm, 5x7mm, silver

Cord, 42cm, Ø 6mm, beige

2x Cord endings, Ø 6mm, silver

4x Head pins, 6cm, silver

8x Jump rings, 4mm, silver

7x Jump rings, 6mm, silver 1x Jump ring, 7mm, silver

4x Mother of pearl cockle pendants, 24mm, white

12x Mother of pearl disc pendants, 25mm, white

1x Spring ring, 7mm, silver Wire, 1m, 0.7mm, silver

Tools

Flat nose pliers

Round nose pliers

Scissors

Side cutter

Toothpick

Tweezers

There are step by step instructions after the picture instructions.

STEP 1: Insert a 4mm jump ring and Swarovski Pendant art. 6731 14mm Crystal AB onto a 6mm jump ring. Repeat this process six more times, but on the last one just use the 6mm jump ring.

STEP 2: Cut 14 6cm long pieces of wire and make a loop at one end to form eye pins.

STEP 3: Insert Swarovski Fancy Stones art. 4195 Crystal F 14mm and 22mm into the Swarovski setting. Gently close prongs using tweezers. Thread the Swarovski Fancy Stones onto a head pin and form a loop at the other end. Cut off excess wire. Repeat this step four more times, but thread the last one onto an eye pin as shown in our illustrations with this step.

STEP 4: Insert the disk pendant and the 4mm jump ring including Swarovski Pendant into the loop of one of the eye pins made in step 2. Thread 4 Swarovski Bead art. 5000 3mm Crystal AB onto the eye pin and then add the shell pendant. Make a loop at the top of the shell pendant as shown.

STEP 5: Attach another eye pin and Swarovski Pendant onto the loop make at the top of the shell pendant in the previous step. Insert 4 more Swarovski Beads and the disk pendants. Repeat this step one more time – see illustrations for clarification.

STEP 6: Insert the Swarovski Fancy Stone art. 4195 14mm into the top most loop of the piece from step 5. Repeat steps 4-6 three more times to get three more similar pieces but of different structure. See illustrations for clarification.

STEP 7: Cut a 10cm long chain and a 42cm long cord. Glue the cord ends into the cord endings. Attach one of them to a spring ring and the second one to a 7mm jump ring.

STEP 8: Attach all the four pieces from steps 4-6 to the chain leaving a spare of 4cm to act as an extension. Attach the last Swarovski Pendant to the last link of this extension.

Have fun making this beautiful Swarovski Crystal jewelry design!

Keep Smiling & Keep Shining!